Please familiarise yourself with the forum, including policy on feature requests, rules & guidelines
Too_Mere
About
- Username
- Too_Mere
- Location
- Chicago, IL, USA
- Joined
- Visits
- 3,920
- Last Active
- Roles
- Beta Tester, Mentor
- Points
- 33
- Location
- Chicago, IL, USA
- YouTube
- https://www.youtube.com/channel/UCnR9j0p9ASp2pR6usJjJ3Rg
- Music Streaming Link (if applicable)
- https://m.soundcloud.com/meremush
- Music Download Link (if applicable)
- https://meremush.bandcamp.com
- Posts
- 993
- 4
- Badges
Comments
-
My pleasure 👍🏼
-
No problem! :-) Just add a blank clip that ends exactly on the next bar, after tails have faded. You should be able to get an exact number of bars that way.
-
Not impossible. I would load the sample into a kit. Adjust the clip length then resample with rec + play as described above. Then you should be able to load that into an audio clip of the same length without warping.
-
@jensg said: ah so maybe this could be the trick? import the file to an audio clip in arranger, lengthen the clip to an even measure and then it should work? This would also need to be the “correct length” to avoid warping.
-
By correct clip length I mean if you export a 4 bar drum loop from your computer you should make sure loads as a 4 bar audio clip on deluge. If it loads as a 3 bar clip, for example, it won’t play as intended. Thus shift + horizontal knob would be n…
-
You should be able to trim the files to exact measures within your DAW/computer. If not, you can adjust the clip lengths before resampling and that should do the trick. The deluge is a loop based sequencer after all. Even Ableton doesn’t allow …
-
Warping is always applied to audio clips. The warping will not affect the audio if the clip length is correct and tempo is set to that of the original (tempo matching can be done by holding the tempo knob and pressing the audio clip). To achieve …
-
No problem 👍🏼
-
Not currently possible, sorry. Reverse is set for all notes of the synth instrument or kit row. You could have the reversed sample on Osc 2 and modulate volumes for single notes though.
-
Maybe try a new battery in the meantime. Good luck!
-
Not sure then. You should probably fill this out then: https://docs.google.com/forms/d/e/1FAIpQLSeTP-eDaaDOmU4-WRXcVhQIoIBd8bkLC_Up4_Lt1RbYZXA-xQ/viewform
-
Even when connected to DC power? If not, I’d open the back and make sure the battery is properly seated, making sure the tabs are holding it tightly. Then I’d try a replacement battery.
-
@TheDarkSide said: I use a dc adaptor and I just tried with a power bank. Still nothing. But I was updating to the new firmware 3.1.5 and there was an Error displaying. When I turned it off and on again then nothing happens. HELP T…
-
No problem 👍🏼
-
I think the problem is that you were pressing shift. Shift + record instantly starts resampling, which is recording the silence before you press play. What you should do is press and hold record and then play (no shift). This begins resampling at …
-
Double check that the write protect switch on the SD card isn’t on. If not, could be a bad card. You should be able to do what you’re describing.
-
You must have your shortcuts set up for the old panel. Go to settings under PADS >SHORtcuts> and change to 3.0.
-
No plans for this that I’m aware of.
-
Not currently possible, sorry. Closest result would be mapping the mutes of clips/tracks to a MIDI controller.
-
Have you tried a factory reset? (Press and hold select knob while powering on)
-
@Kang_Kodus said: Thank you for the tip. Unfortunately it does not help. It seems to be a problem that occurs after some time playing. Only restarting helps to get back in sync. Which is not the best solution, playing live. If you press t…
-
@Stick44 said: Thanks,, But Im using a new SD (32) card which I have a Library of wav Samples .When loaded,it just reads 'FOLD' (folder I take it ) and wont read ? I Formatted the SD card with FAT 32 but do I need the Factory Samples Directory F…
-
You’ll need a card reader for the PC if one’s not built in. You cannot access the SD contents over Deluge’s USB. Just put the samples where you’d like in the SAMPLES folder.
-
That usually happens when there’s notes already sequenced in the clip. Clear out the clip first or create a new blank clip before turning it into an audio clip.
-
No problem! That’s not currently possible on the Deluge, sorry.
-
That’s something you’d have to set up on the external synth.
-
Firmware 3.1.5 is the latest. Make sure you’re on the latest as they include bug fixes. If you are on 3.1.5, can you list steps to reproduce the crash?
-
No problem. I’m fairly certain a firmware update of this is not possible. No way to split stereo signals in that way, sorry.
-
@tomblue said: Is the hardware capable of monitoring all audio via the headphones while routing specific tracks out through the outputs? This feature would massively open up the routing options for including external signal processors I b…
-
No problem! Initially only numbers were possible. So they still come that way for consistency sake I suppose. It’s a good opportunity to add the prefixes anyway. Makes finding what you need much easier. 👍🏼